Notes for the TI-83, 83+, 84, 84+ Calculators

Adapted by John Morgan Russell; from Barbara Illowsky and Susan Dean, David Diez, Mine Cetinkaya-Rundel and Christopher D. Barr; Julie Vu and David Harrington

Notes for the TI-83, 83+, 84, 84+ Calculators

Quick Tips

Legend

represents a button press
[ ] represents yellow command or green letter behind a key
< > represents items on the screen

To adjust the contrastPress 2nd key , then hold arrow up to increase the contrast or arrow down to decrease the contrast.

To capitalize letters and wordsPress alpha key to get one capital letter, or press 2nd key , then to set all button presses to capital letters. You can return to the top-level button values by pressing again.

To correct a mistakeIf you hit a wrong button, just hit clear key and start again.

To write in scientific notationNumbers in scientific notation are expressed on the TI-83, 83+, 84, and 84+ using E notation, such that…

4.321 E 4 = $\text{4}\text{.321}×{\text{10}}^{4}$
4.321 E –4 = $\text{4}\text{.321}×{\text{10}}^{-4}$

To transfer programs or equations from one calculator to another:Both calculators: Insert your respective end of the link cable cable and press 2nd key , then [LINK].

Calculator receiving information:

Use the arrows to navigate to and select <RECEIVE>
Press .

Calculator sending information:

Press appropriate number or letter.
Use up and down arrows to access the appropriate item.
Press to select item to transfer.
Press right arrow to navigate to and select <TRANSMIT>.
Press .

Note

ERROR 35 LINK generally means that the cables have not been inserted far enough.

Both calculators: Insert your respective end of the link cable cable Both calculators: press 2nd key , then [QUIT] to exit when done.

Manipulating One-Variable Statistics

Note

These directions are for entering data with the built-in statistical program.

Sample Data We are manipulating one-variable statistics.
Data	Frequency
–2	10
–1	3
0	4
1	5
3	8

To begin:

Turn on the calculator.
Access statistics mode.
Select <4:ClrList> to clear data from lists, if desired.
,
Enter list [L1] to be cleared.
, [L1] ,
Display last instruction.
, [ENTRY]
Continue clearing remaining lists in the same fashion, if desired.
, , [L2] ,
Access statistics mode.
Select <1:Edit . . .>
Enter data. Data values go into [L1]. (You may need to arrow over to [L1]).
- Type in a data value and enter it. (For negative numbers, use the negate (-) key at the bottom of the keypad).
  , ,
- Continue in the same manner until all data values are entered.
In [L2], enter the frequencies for each data value in [L1].
- Type in a frequency and enter it. (If a data value appears only once, the frequency is “1”).
  ,
- Continue in the same manner until all data values are entered.
Access statistics mode.
Navigate to <CALC>.
Access <1:1-var Stats>.
Indicate that the data is in [L1]…
, [L1] ,
…and indicate that the frequencies are in [L2].
, [L2] ,
The statistics should be displayed. You may arrow down to get remaining statistics. Repeat as necessary.

Drawing Histograms

Note

We will assume that the data is already entered.

We will construct two histograms with the built-in STATPLOT application. The first way will use the default ZOOM. The second way will involve customizing a new graph.

Access graphing mode.
, [STAT PLOT]
Select <1:plot 1> to access plotting – first graph.
Use the arrows navigate go to <ON> to turn on Plot 1.
<ON> ,
Use the arrows to go to the histogram picture and select the histogram.
Use the arrows to navigate to <Xlist>.
If “L1” is not selected, select it.
, [L1] ,
Use the arrows to navigate to <Freq>.
Assign the frequencies to [L2].
, [L2] ,
Go back to access other graphs.
, [STAT PLOT]
Use the arrows to turn off the remaining plots.
Be sure to deselect or clear all equations before graphing.

To deselect equations:

Access the list of equations.
Select each equal sign (=).
Continue, until all equations are deselected.

To clear equations:

Access the list of equations.
Use the arrow keys to navigate to the right of each equal sign (=) and clear them.
Repeat until all equations are deleted.

To draw default histogram:

Access the ZOOM menu.
Select <9:ZoomStat>.
The histogram will show with a window automatically set.

To draw custom histogram:

Access window mode to set the graph parameters.
- ${X}_{\mathrm{min}}=-2.5$
- ${X}_{\mathrm{max}}=3.5$
- ${X}_{scl}=1$ (width of bars)
- ${Y}_{\mathrm{min}}=0$
- ${Y}_{\mathrm{max}}=10$
- ${Y}_{scl}=1$ (spacing of tick marks on y-axis)
- ${X}_{res}=1$
Access graphing mode to see the histogram.

To draw box plots:

Access graphing mode.
, [STAT PLOT]
Select <1:Plot 1> to access the first graph.
Use the arrows to select <ON> and turn on Plot 1.
Use the arrows to select the box plot picture and enable it.
Use the arrows to navigate to <Xlist>.
If “L1” is not selected, select it.
, [L1] ,
Use the arrows to navigate to <Freq>.
Indicate that the frequencies are in [L2].
, [L2] ,
Go back to access other graphs.
, [STAT PLOT]
Be sure to deselect or clear all equations before graphing using the method mentioned above.
View the box plot.
, [STAT PLOT]

Linear Regression

Sample Data

The following data is real. The percent of declared ethnic minority students at De Anza College for selected years from 1970–1995 was:

The independent variable is “Year,” while the independent variable is “Student Ethnic Minority Percent.”
Year	Student Ethnic Minority Percentage
1970	14.13
1973	12.27
1976	14.08
1979	18.16
1982	27.64
1983	28.72
1986	31.86
1989	33.14
1992	45.37
1995	53.1

Student Ethnic Minority Percentage

By hand, verify the scatterplot above.

This is a scatterplot for the data provided. Year is plotted on the horizontal axis and percent is plotted on the vertical axis. The points show a strong, curved, upward trend.

Note

The TI-83 has a built-in linear regression feature, which allows the data to be edited.The x-values will be in [L1]; the y-values in [L2].

To enter data and do linear regression:

ON Turns calculator on.
Before accessing this program, be sure to turn off all plots.
- Access graphing mode.
  , [STAT PLOT]
- Turn off all plots.
  ,
Round to three decimal places. To do so:
- Access the mode menu.
  , [STAT PLOT]
- Navigate to <Float> and then to the right to <3>.
- All numbers will be rounded to three decimal places until changed.
Enter statistics mode and clear lists [L1] and [L2], as describe previously.
,
Enter editing mode to insert values for x and y.
,
Enter each value. Press to continue.

To display the correlation coefficient:

Access the catalog.
, [CATALOG]
Arrow down and select <DiagnosticOn>
… , ,
$r$ and ${r}^{2}$ will be displayed during regression calculations.
Access linear regression.
Select the form of y = a + bx.
,

The display will show:

LinReg

y = a + bx
a = –3176.909
b = 1.617
r = 2 0.924
r = 0.961

This means the Line of Best Fit (Least Squares Line) is:

y = –3176.909 + 1.617x
Percent = –3176.909 + 1.617 (year #)

The correlation coefficient r = 0.961

To see the scatter plot:

Access graphing mode.
, [STAT PLOT]
Select <1:plot 1> To access plotting – first graph.
Navigate and select <ON> to turn on Plot 1.
<ON>
Navigate to the first picture.
Select the scatter plot.
Navigate to <Xlist>.
If [L1] is not selected, press , [L1] to select it.
Confirm that the data values are in [L1].
<ON>
Navigate to <Ylist>.
Select that the frequencies are in [L2].
, [L2] ,
Go back to access other graphs.
, [STAT PLOT]
Use the arrows to turn off the remaining plots.
Access window mode to set the graph parameters.
- ${X}_{\mathrm{min}}=1970$
- ${X}_{\mathrm{max}}=2000$
- ${X}_{scl}=10$ (spacing of tick marks on x-axis)
- ${Y}_{\mathrm{min}}=-0.05$
- ${Y}_{\mathrm{max}}=60$
- ${Y}_{scl}=10$ (spacing of tick marks on y-axis)
- ${X}_{res}=1$
Be sure to deselect or clear all equations before graphing, using the instructions above.
Press the graph button to see the scatter plot.

To see the regression graph:

Access the equation menu. The regression equation will be put into Y1.
Access the vars menu and navigate to <5: Statistics>.
,
Navigate to <EQ>.
<1: RegEQ> contains the regression equation which will be entered in Y1.
Press the graphing mode button. The regression line will be superimposed over the scatter plot.

To see the residuals and use them to calculate the critical point for an outlier:

Access the list. RESID will be an item on the menu. Navigate to it.
, [LIST], <RESID>
Confirm twice to view the list of residuals. Use the arrows to select them.
,
The critical point for an outlier is: where:
- $n$ = number of pairs of data
- $\mathrm{SSE}$ = sum of the squared errors
- $\sum _{}^{}{\mathrm{residual}}^{2}$
Store the residuals in [L3].
, , [L3] ,
Calculate the [latex]\frac{{\mathrm{\left(residual\right)}}^{2}}{n-2}\). Note that $n-2=8$
, [L3] , , ,
Store this value in [L4].
, , [L4] ,
Calculate the critical value using the equation above.
, , , , , [V] , , [LIST] , , , , [L4] , , ,
Verify that the calculator displays: 7.642669563. This is the critical value.
Compare the absolute value of each residual value in [L3] to 7.64. If the absolute value is greater than 7.64, then the (x, y) corresponding point is an outlier. In this case, none of the points is an outlier.

To obtain estimates of y for various x-values:There are various ways to determine estimates for “y.” One way is to substitute values for “x” in the equation. Another way is to use the trace key on the graph of the regression line.

TI-83, 83+, 84, 84+ instructions for distributions and tests

Distributions

Access DISTR (for “Distributions”).

For technical assistance, visit the Texas Instruments website at http://www.ti.com and enter your calculator model into the “search” box.

Binomial Distribution

binompdf(n,p,x) corresponds to P(X = x)
binomcdf(n,p,x) corresponds to P(X ≤ x)
To see a list of all probabilities for x: 0, 1, . . . , n, leave off the “x” parameter.

Poisson Distribution

poissonpdf(λ,x) corresponds to P(X = x)
poissoncdf(λ,x) corresponds to P(X ≤ x)

Continuous Distributions (general)

$-\infty$ uses the value –1EE99 for left bound
$\infty$ uses the value 1EE99 for right bound

Normal Distribution

normalpdf(x,μ,σ) yields a probability density function value (only useful to plot the normal curve, in which case “x” is the variable)
normalcdf(left bound, right bound, μ, σ) corresponds to P(left bound < X < right bound)
normalcdf(left bound, right bound) corresponds to P(left bound < Z < right bound) – standard normal
invNorm(p,μ,σ) yields the critical value, k: P(X < k) = p
invNorm(p) yields the critical value, k: P(Z < k) = p for the standard normal

Student’s t-Distribution

tpdf(x,df) yields the probability density function value (only useful to plot the student-t curve, in which case “x” is the variable)
tcdf(left bound, right bound, df) corresponds to P(left bound < t < right bound)

Chi-square Distribution

Χ²pdf(x,df) yields the probability density function value (only useful to plot the chi² curve, in which case “x” is the variable)
Χ²cdf(left bound, right bound, df) corresponds to P(left bound < Χ² < right bound)

F Distribution

Fpdf(x,dfnum,dfdenom) yields the probability density function value (only useful to plot the F curve, in which case “x” is the variable)
Fcdf(left bound,right bound,dfnum,dfdenom) corresponds to P(left bound < F < right bound)

Tests and Confidence Intervals

Access STAT and TESTS.

For the confidence intervals and hypothesis tests, you may enter the data into the appropriate lists and press DATA to have the calculator find the sample means and standard deviations. Or, you may enter the sample means and sample standard deviations directly by pressing STAT once in the appropriate tests.

Confidence Intervals

ZInterval is the confidence interval for mean when σ is known.
TInterval is the confidence interval for mean when σ is unknown; s estimates σ.
1-PropZInt is the confidence interval for proportion.

Note

The confidence levels should be given as percents (ex. enter “95” or “.95” for a 95% confidence level).

Hypothesis Tests

Z-Test is the hypothesis test for single mean when σ is known.
T-Test is the hypothesis test for single mean when σ is unknown; s estimates σ.
2-SampZTest is the hypothesis test for two independent means when both σ’s are known.
2-SampTTest is the hypothesis test for two independent means when both σ’s are unknown.
1-PropZTest is the hypothesis test for single proportion.
2-PropZTest is the hypothesis test for two proportions.
Χ²-Test is the hypothesis test for independence.
Χ²GOF-Test is the hypothesis test for goodness-of-fit (TI-84+ only).
LinRegTTEST is the hypothesis test for Linear Regression (TI-84+ only).

Note

Input the null hypothesis value in the row below “Inpt.” For a test of a single mean, “μ∅” represents the null hypothesis. For a test of a single proportion, “p∅” represents the null hypothesis. Enter the alternate hypothesis on the bottom row.

From 2.3: Displaying Quantitative Data

Here are calculator instructions for entering data and for creating a customized histogram. Create a histogram.

Calculator Instructions

Press Y=. Press CLEAR to delete any equations.
Press STAT 1:EDIT. If L1 has data in it, arrow up into the name L1, press CLEAR and then arrow down. If necessary, do the same for L2.
Into L1, enter 1, 2, 3, 4, 5, 6.
Into L2, enter 11, 10, 16, 6, 5, 2.
Press WINDOW. Set Xmin = .5, Xmax = 6.5, Xscl = (6.5 – .5)/6, Ymin = –1, Ymax = 20, Yscl = 1, Xres = 1.
Press 2^nd Y=. Start by pressing 4:Plotsoff ENTER.
Press 2^nd Y=. Press 1:Plot1. Press ENTER. Arrow down to TYPE. Arrow to the 3^rd picture (histogram). Press ENTER.
Arrow down to Xlist: Enter L1 (2^nd 1). Arrow down to Freq. Enter L2 (2^nd 2).
Press GRAPH.
Use the TRACE key and the arrow keys to examine the histogram.Frequency PolygonsFrequency polygons are analogous to line graphs, but instead utilize binning techniques to make continuous data visually easy to interpret. It is essentially a combination of a histogram and line graph.

License

Icon for the Creative Commons Attribution-ShareAlike 4.0 International License

MATH 1260: Significant Statistics Copyright © 2020 by John Morgan Russell, OpenStaxCollege, OpenIntro is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License, except where otherwise noted.

Quick Tips

Manipulating One-Variable Statistics

Drawing Histograms

Linear Regression

Sample Data

TI-83, 83+, 84, 84+ instructions for distributions and tests

Distributions

Tests and Confidence Intervals

License

Share This Book